E-line ELI-PRO3 series Especificaciones

Installation & Operation manualElite 5X, Mark 5X, Mark 5X Pro & Elite 4X Operation manual

8PagesSonar PageDisplays the water column moving from right to left on your unit’s screen. On the right side of the screen, the Amplitude Scope bar pr

9PagesOverlay DataDisplays selected overlay data on the sonar page.ShowEnables/disables the display of overlay data, allow-ing you to remove overlay d

10PagesTo select overlay data:1. From the sonar page, press MENU. 2. Select Overlay data and press ENTER. 3. Select Congure and press ENTER.

11SonarMove the blue sonar history bar all the way to the right to resume normal sonar scrolling.Press MENU and select Exit cursor mode to re-move t

12SonarPress MENU from any sonar page to access the So-nar menu. Adjust (Advanced Mode only)Used to make adjustments to Sensitivity, Colorline and Gra

13SonarMark series units have a monochrome display,so wide bands of gray indicate a hard sonarreturn, while softer returns are shown as dark,narrow ar

14SonarSplit FlasherSplit ZoomFrequency Controls the transducer frequency used by the unit. This unit supports two frequencies: 200kHz and 83kHz. 200

15SonarFish IDDisplays sh echoes as sh sym-bols instead of sh arches. Fish ID is not the most accurate method of sh detection since structure and

16SonarOverlay DataAllows you to select data (wa-ter temperature, depth, etc) to be displayed on top of the Sonar screen. Overlay data setup is covere

17SettingsSettings MenuAccesses to installation and conguration settings for your unit. SystemAdjusts unit settings like language, mute audio and adv

Copyright © 2011 NavicoAll rights reserved.Lowrance® and Navico® are registered trademarks of Navico. Navico may nd it necessary to change or end our

18SettingsSet LanguageSelects the language used on menus and text boxes. Mute AudioTurns on/o unit audio, like key beeps, alarm sounds, etc.Advanced

19SettingsSonar Used to make adjustments to Sonar options and display settings like Noise Rejection, Surface and Fishing Mode. Noise RejectionUses adv

20SettingsInstallationProvides access to Keel Oset and Temp Calibration settings.Keel OffsetAll transducers measure water depth from the transducer t

21SettingsBefore setting keel oset, measure the distance from the transducer to the lowest part of the keel. If, for example, the keel is 3.5 feet be

22IndexAAbout 18Advanced Mode 6Alarms 21Fish 21Shallow 21Amplitude Scope 15Auto Sensitivity 13CColor 15Colorline 12Cursor 6Custom Range 13D

SpecicationsElite 5x, Mark 5x & Mark 5x ProGeneralCase size5.4” H (134mm) x 6.8” W (174mm); 6” H (152mm) with bracketDisplayMark: (5” diagonal) H

SpecicationsElite 4xGeneralCase size5.6” H (144mm) x 3.7” W (94.3mm); 6.4” H (164mm) with bracketDisplay (3.5” diagonal) 320x240 (256 color) TFT LCDB

How to Obtain Service… …in the USA:Contact the Factory Customer Service Department. Call toll-free:800-324-13568 a.m. to 5 p.m. Central Standard Time

© Copyright 2011All Rights ReservedNavico Holding AS*988-10157-001*Visit our website:www.lowrance.com

1Table of ContentsIntroduction ... 2Basic Operation ... 3Setup wizard ...

2IntroductionGetting StartedTurn unit on/offTo turn on/off the unit, press and hold the LIGHT/POWER key for three seconds. Adjusting the backlightThi

3Basic OperationSetup wizardThe Setup wizard will appear when the unit is turned on for the rst time. To choose your own settings, do not run the set

4Basic OperationOn/Off featuresSelect an on/o menu item and press ENTER to turn it on/o.Dropdown menusAfter accessing the dropdown menu, press the k

5Basic OperationTo input text:1. Use the keypad to select the desired character and press ENTER. 2. Repeat Step 1 for each character. 3. When en

6Basic OperationAdvanced Mode Enables advanced features and settings.The following features are enabled when Advanced mode is turned on:• Colorline (

7Basic OperationStandby modeLowers power consumption by turning o sonar and the display. Press the PWR/LIGHT key to ac-cess the Backlight menu. Selec